- AD-Net
- Video Audio Transmission Equipment
- RCA & XLR Audio Over Fiber Extenders
- HD Video Transmission
- CCTV Video/Audio/Data
- HDMI KVM Over Fiber
- HDMI KVM Over UTP Cat5e/Cat6
- VGA KVM Over Fiber
- VGA KVM Over UTP Cat5e/Cat6
- DVI KVM Over Fiber
- DVI KVM Over UTP Cat5e/Cat6
- AHD CVI TVI CVBS Over Fiber
- HDMI Over Wired & Wireless LAN
- USB Over Fiber Extenders
- Video Baluns (Video Over UTP Cat5)
- HD AHD/TVI/CVI Video Baluns
- HD AHD/TVI/CVI/CVBS Active Video Baluns
- FTTX Access
- Fiber Modules
- Industrial Communication Products
- Media Converters
- Fiber Optical Multiplexers
- n x E1 G.703 Series Fiber Multiplexer
- n x E1 G.703 Series + Ethernet Series
- Serial & CANBUS Fiber Modem Series (V.35/RS422/485/232)
- SNMP Managed n x E1/V35/ETH Fiber Multiplexer
- STM1/E3/DS3/T3 Fiber Mux Series
- Voice Over Fiber Mux Series
- Rack Mount Chassis
- CWDM Multiplexing Systems
- Optical Line Protection Equipment
- Interface Converters
- Passive Optical Equipment
- SDH/MSPP Systems
- Switches
- Video Audio Transmission Equipment
- Tainet
- Four-Faith
Catacomm Corporation
Sdn Bhd
Unit E1-29-6, Block E1,
Dataran Prima, Jalan PJU 1/42,
47301 Petaling Jaya,
Selangor, Malaysia.
+603-7803 8228
+603-7803 8228
clyeow@catacomm-corp.comMain control card for modular AN-E OLT8000, supports, SNMP MIB, EMS system and control functions
Previous | 6 / 8 | Next |
Description
AN-8000-M is a module that must be installed in AN-E-OLT8000 to get it work, and at least 1 SFP module for uplink must be installed. More modules can be added later as your network grows. AN-8000-M performs 2 main functions exchange and control. Exchange part provides 2 layers of exchange functions to PON module cards, and control port gives control function possibilities for all GEPON system. Core part of the board is 16 port GB chip – 8 ports are connected to uplink SFP’s, and another 8 – to downlink PON modules further connected to ONU’s.
Features
-
8 x 1.25 GB SFP slot uplinks to network (switches, routers, IP-PABX, or IPTV servers)
-
Uplink ports can accept any kind and distance and SFP’s, also UTP type SFP’s
-
If configured under electric UTP type port, it can work in adaptive 10/100/1000 Mbit/s modes
-
Supports VLAN division per ports
-
Supports 802.1Q, 802.1P protocols
-
Up to 4096 entries for VLAN’s
-
Capacity for supported MAC addreses is 16K
-
Supports broadcast restrain function in down links, this can protect PON network from influence of broadcast storms
-
Supports broadcast discharge which is permitted by bandwidth granuality configuration based on 64Kbit/s
-
Supports ports convergence function – up to 8 converged ports are supported, which means converged port BW can be up to 8 Gbit/s.
-
Offers 2 control interfaces, local and network
-
Support 3 types of management: CLI, TELNET and SNMP
-
Network control supports in-band and out-band
-
Memory capacity 16M – which can store big amounts of configuration
-
Real time fault alarms by indicators and in EMS
Specifications
Power consumption >15 W (please check whole chassis specifications here)
Uplink data ports specifications:
Number of ports: 8
Form: SFP type
Voltage: 3.3V
Speed: for Optical modules 1000M full duplex, for Electrical type (such as this) – 10/100/1000 adaptive
Console port:
Interface type: RJ-45, console cable RJ45/DB comes in set
Speed: 9600 Bit/s
Outband network management interface:
Standard: IEE802.3
Transmission speed: 10M Full duplex
Cable: RJ-45, use cross cable to connect to PC, or straght to connect to HUB
Distance 100 m
Ordering Information
AN-8000-M
|
Main control card for modular OLT – supports, SNMP MIB, EMS system and control functions (must be inlcuded in each chassis).
|