Catacomm Corporation
Sdn Bhd

Unit E1-29-6, Block E1,
Dataran Prima, Jalan PJU 1/42,
47301 Petaling Jaya,
Selangor, Malaysia.
+603-7803 8228
+603-7803 8228

Industrial Type Ethernet LAN Extender

Previous 7 / 11 Next

Industrial Type Ethernet LAN Extender High Speed LAN & Ethernet Over Copper Extenders Interface Converters AD-Net Industrial Type Ethernet LAN Extender High Speed LAN & Ethernet Over Copper Extenders Interface Converters AD-Net Industrial Type Ethernet LAN Extender High Speed LAN & Ethernet Over Copper Extenders Interface Converters AD-Net
Add Quotation


AN-LAN-EXT-ENH-200-I Industrial Ethernet Extender is single channel high-speed Ethernet transmission device. It can simultaneously transmit Ethernet and Power over any 2-wire cable, such as Cat5, coaxial cable, telephone line, power line and so on. The Max transmission distance can reach 1,000m, and the Max bandwidth can reach 200Mbps.
This device contains the Master and Slave Unit, which supports point to point and point to multi-point network transmission. Now it has two type terminals BNC and 2P connector for your choice, which can be directly used with coaxial cable or 2-wire cable. It can greatly simplify the project cabling, applied to expand network system and transmit long distance PoE device signals.


  • Max transmission distance can reach 1,000m (RVS 2×1mm2).
  • Max physical bandwidth can reach 200Mbps.
  • Support power over coax technology (1257VDC/POE).
  • Transparent transmission, no adjustment and no need to change the upper software.
  • 35mm guide rail type installation, plug and play, anti-interference ability design.


Available Voltage Range
Power Consumption
≤5W / PC
Transmission / Rate
Standard Compliance
IEEE1901, IEEE802.3
Up down Agreement
Physical Speed
Encryption Way
128-bit AES Encryption
30000 hours
Physical Characteristic
Dimension (L × W × H)
Net Weight
Operating Environment
Working Temperature
Storage Temperature
Working Humidity
2085% Non-condensation
Storage Humidity
1090 Non-condensation


Cable Tips
Telephone Line: Category 3 or above
Power line: RVV / RVS / RVVP / RVB 2×0.5mm2 above
UTP Cable: Cat5 or above
Coaxial cable: RG59 or above
Accessories Spec
RJ45 port by EIA / TIA568B
BNC/2-wire Converter (Optional)
Power Adapter: 48~57VDC regulated power supply, 5mm female power port (Optional)
Installation instructions

 Installation Diagram

  1. This product supports PoC and PoE equipment to use. Within 500m distance, you only need to connect the PoE power supply equipment to Master unit. The Slave unit and remote PoE devices all can be poweredschemes
  2. When the Master uses 48 ~ 57VDC power adapter to supply power, within 500m distance, the Slave unit and remote PoE devices all can be powered. If the transmission distance is longer (for example 1000m), the power loss is bigger. You can supplement access to 48 ~ 57VDC power adapter for Slave unit. The remote PoE devices can be powered.
  3. If the remote devices are not PoE devices, you can offer 12VDC power supply for the Master and Slave unit separately, the remote devices are needed to be powered separately.schemes3
 Notes: In order to ensure the power supply with low transmission loss, we suggest that customers use high quality cables such as coaxial cables: above RG59, 2-wire cable: above 2×0.75mm2, network cable: Cat5 or above.
Network Data Rate
The graph below shows AN-LAN-EXT-ENH-200-I transmission distance and network data rate. The data differs from the cables types. When you use this device, please choose the suitable cables in line with your demands.
The above data for TCP throughput is the measured data in the actual environment. The maximum physical layer data is 200Mbps. For coaxial cable transmission, performance is more stable, but it also affected by the cable and terminal matching methods. The above tests are all finished in the field test.

Installation Diagram

Figure 1- Basic Connection
Figure 2- Bus-architecture Connection
Figure 3-Daisy Chain Connection
Figure 4- Multicast
Tips: For a lot of front-end network equipment, you can use a network switch to collect. When more network devices are connected, you can choose 16 Channel Ethernet Extender Hub.

Use Tips

When you use AN-LAN-EXT-ENH-200-I, please follow the below tips as a reference, in order to reduce the fault in the process of using and the inspection work.
  1. The product can be set master-slave side and grouped by the software, please place Master in the Local network equipment for easily power supply.
  2. The signal transmission coaxial cable must be the international standard (RG59 or above). Poor quality coaxial cable can not transmit signal.
  3. Long distance cable connection must be formal connection methods, such as welding or using connectors. Pay attention to the quality of BNC terminal.
  4. Make sure the electrode of transmission cable is consistent, otherwise, it is easy to cause the power failure.
  5. Please choose matching power supply(12VDC or 4857VDC).
  6. There is no waterproof design for this product, please make sure it is used in dry environment.
  7. If device fails, do not disassemble or repair it by yourself. Please contact us timely.

Ordering Information

Industrial Type Ethernet LAN Extender, transmit Ethernet and Power over any 2-wire cable.

Please leave your enquiry here, we will reply as soon as possible.
Company Name  
Product Interested  
Contact No.*  
*only support gif, jpeg, jpg, png, pdf

You have 0 items in you cart. Would you like to checkout now?
0 items
Switch to Mobile Version
Subscribe Newsletter