Catacomm Corporation
Sdn Bhd

Unit E1-29-6, Block E1,
Dataran Prima, Jalan PJU 1/42,
47301 Petaling Jaya,
Selangor, Malaysia.
+603-7803 8228
+603-7803 8228
clyeow@catacomm-corp.com

PoE Type 4 E1 to Ethernet Converter

Previous 4 / 45 Next

PoE Type 4 E1 to Ethernet Converter E1/T1 Interface Converter Series Interface Converters AD-Net PoE Type 4 E1 to Ethernet Converter E1/T1 Interface Converter Series Interface Converters AD-Net
Quantity
Add Quotation


This interface converter is based on FPGA, using reverse direction multiplexing technology to bundle for multiple E1 circuits to transmit the Ethernet data of 4Channel 100BASE-TX. It can realize 1~4 E1 channel to convert between Ethernet optical interface. This device can transmit the transceiver signal point to point to Ethernet optical interface to make E1 channels interconnected with Ethernet optical interface. Unlike general remote network bridge, this device can support 1-4Channel E1 channel configuration, can automatically detect the number of E1 and select the E1 available. It allows E1 lines transmission time delay difference.

Features

  • Based on self -copyright IC
  • To achieve Ethernet data transparent transmission in 1-4E1 circuits
  • Can realize the local and the remote device reset
  • Ethernet Interface is 100BASE-FX, support VLAN protocol
  • Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering function
  • Single Channel lines rate is 1984Kbit/s, 4Channel Bandwidth is up to 7936Kbit/s
  • Channel 10M/100M Ethernet interface can isolate each other to realize communication independently
  • Ethernet interface supports10M/100M, half/full duplex auto- adaptable and AUTO-MDIX  (crossed line and straightly connected line self-adaptable )
  • CRC automatic alarm threshold can be set to isolate the poor quality transmission lines and cut off a single-direction. When 2M branch circuit onedirection error rate exceeds threshold, cutting off this direction the other direction is not affected; that is to say, both of the Ethernet directiontransmission can be asymmetric
  • Allow 4-Channel E1 transmission time delay difference 100ms. When the margin exceed the allowed range, the system can automatically stop on the E1 that time delay is too large to send data
  • E1 interface conform to ITU-T G.703, G.704 and G.823, not support the use of signal timeslot
  • E1 interface module with inter-set clock recovery circuit and HDB3 code circuit
  • Support E1 channel hot-plug in the device, and automatically detects the effective E1 channel and will not interrupt data transmission
  • Can support 1-4Channel E1 channel configuration, can automatically detect the number of E1 and select the E1 available;
  • Ethernet supports standard IEEE802.3af / at power supply; Each port can be sufficient power output 15.4W (IEEE802.3af), at 25.5W (IEEE802.3at);

Specification

E1 Interface
  • Interface Standard£ºcomply with protocol G.703;
  • Interface Rate£ºn*64Kbps±50ppm;
  • Interface Code£ºHDB3;
  • E1 Impedance£º75Ω (unbalance), 120Ω (balance);
  • Jitter tolerance£ºIn accord with protocol G.742 and G.823
  • Allowed Attenuation£º0~6dBm
Ethernet interface(10/100M)
  • Interface rate£º10/100 Mbps, half/full duplex auto-negotiation
  • Interface Standard£ºCompatible with IEEE 802.3, IEEE 802.1Q (VLAN)
  • MAC Address Capability£º4096
  • Connector£ºRJ45, support Auto-MDIX
Ethernet POE features
  • PoE standard£ºIEEE 802.3af / at
  • PoE Type£ºEnd Crossing Method (optional intermediatebridging method)
  • PoE Port Features£ºPort output power 15.4W /25.5W
  • PoE transmission core£º1/2 +, 3/6-pair (optional 4/5+, 7/8-pair)
Working environment
  • Working temperature£º-10°C ~ 50°C
  • Working Humidity£º5%~95 % (no condensation)
  • Storage temperature£º-40°C ~ 80°C
  • Storage Humidity£º5%~95 % (no condensation)
Functional Description POE 4E1/FE interface Converter
Port Description 4* E1 interface£»FE Interface
Power Power supply: AC180V ~ 260V£»DC –48V£»DC +24V
Power consumption: ≤10W
Dimension Product Size: Mini type 216X140X31mm (WXDXH),1.3KG/piece



Description

This interface converter is based on FPGA, using reverse direction multiplexing technology to bundle for multiple E1 circuits to transmit the Ethernet data of 4Channel 100BASE-TX. It can realize 1~4 E1 channel to convert between Ethernet optical interface. This device can transmit the transceiver signal point to point to Ethernet optical interface to make E1 channels interconnected with Ethernet optical interface. Unlike general remote network bridge, this device can support 1-4Channel E1 channel configuration, can automatically detect the number of E1 and select the E1 available. It allows E1 lines transmission time delay difference.

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

You have 0 items in you cart. Would you like to checkout now?
0 items
Switch to Mobile Version
Subscribe Newsletter